XIO-DI8 : 8 Channel Digital Input Board
$127.00
(Each, Qty.: 1 - 9, U.S. Dollars)
(Each, Qty.: 1 - 9, U.S. Dollars)
- Allows an 8-bit digital input port to monitor combinations of AC and DC voltage input signals
- 500V isolation between Host and field signals
- Hardware programmable input voltage range on each channel
- Dual IDC input headers support two common digital I/O pin-outs
- Input filters ensure reliable measurement of AC or noisy DC signals
- Works with products from SCIDYNE and as well as from other manufactures
You may also be interested
in these items:
XIO-RO8
#100-7632
8 Channel Relay Output Board
Cable Assembly
#115-7623/5018
Flat ribbon cable with IDC connector on each end.
GPIO-104
#100-7602
General purpose Analog and Digital I/O for PC/104 Bus
DIO96-104
#100-7618
High-Density, 96-Bit Digital I/O for PC/104 Bus
- Description
- Specifications
- Ordering Details
- Additional Information
The XIO-DI8 performs the interface function of isolating and conditioning input voltage signals
into levels compatible with standard 8-bit TTL/CMOS digital ports such as those found on Single-Board-Computers.
Eight optically isolated and non-polarized input channels allows any combination of DC or AC signals to be
monitored. The input voltage range for each channel is individually configured by means of a socketed
resistor. In addition, low-pass filters can be selectively enabled for the reliable measurement of AC or noisy
DC signals. The eight conditioned channels form a byte where each bit reflects the state of one input, Bit-0 =
IN0, Bit-1 = IN1 and so on. Activated inputs cause a logic "1" to appear in the associated bit
position. Activated inputs cause a logic "1" to appear in the corresponding bit position. The byte is
buffered and drives one of three possible Host digital input ports. Which Host port will be used is
determined by installing a single resistor network in one of three corresponding DIP sockets. This routes the
output byte to only the designated Host input port. The two remaining Host ports remain unaffected and
available for other purposes. Dual IDC headers directly support the two most common Host digital port pinout
arrangements. Other pinouts are easily accommodated using custom cable assemblies. Field wiring is made through
a single 16-position removable screw-terminal strip which accepts wires in the range of 12-24 AWG. Field
wiring is made through a single 16-position removable screw-terminal strip which accepts wires in the range of
12-24 AWG. The XIO-DI8 operates from a single +5Vdc supply which can be provided by the Host, through either of
the IDC headers, or externally by means of a two-position removable screw-terminal strip. For ease of
installation, the board can be mounted in one of three ways: placed within a 3" SNAPTRACK® (121-0003),
by using standoffs or by attaching it to a DIN rail using optional SNAPTRACK® adapter clips (121-0004).
General:
| Description: | Eight channel optically-isolated digital input interface board |
|---|---|
| Power Requirement: | +5Vdc ±5% @ 125mA typical. Host or Externally supplied, Power-On LED |
| Environmental: | Operating temperature: -20°C to 70°C Non-condensing relative humidity: 5% to 95% |
| Dimensions: | 3.00" W x 9.50" L x 1.35" H |
| Mounting: | Mount using Standoffs, SNAPTRACK® or DIN Rail |
| Isolation: |
500V DC or AC, input-to-output Isolation between adjacent input channels: 250V maximum |
Digital Inputs from Field:
| General: | Eight independent non-polarized optically isolated inputs, Status LEDs |
|---|---|
| Connections: | 16-position removable screw-terminal strip, accepts wires 12-24 AWG |
| Input Voltage: |
Each channel is programmable by means of a socketed resistor DC: 3V minimum, 250V maximum, non-polarized AC: 3VPP minimum, 250VPP maximum, 40hz to 1khz |
| Input Current: | 3.5ma Minimum, 25ma Maximum per input |
| Input Power: | 1.4watts Maximum per input |
| Propagation Delay: |
Input channel to output bit. Measured with 5Vinput signal, Rin = 1kΩ Filter Disabled: On: 40μs Off: 100μs Filter Enabled: On: 20ms Off: 85ms |
| AC Input Filter: | RC type Low-Pass. Switch selectable on a per input basis |
Digital Output to Host:
| General: | Drives one of three 8-bit ports, Port selected by DIP resistor network |
|---|---|
| Connections: | 50-Pin and 26Pin IDC headers. Supports the two most common pinouts |
| Output Levels: |
TTL/CMOS compatible Logic "0": 1.35Vdc maximum Logic "1": 3.15Vdc minimum |
| Output Impedance: | Driven port: 47Ω, primarily from output resistor network |
Questions or Ready to Order? Call 1-877-SCIDYNE
Ordering Details
| Stock Number: | 100-7656 | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Name: | XIO-DI8 | ||||||||||||
| Description: | 8 Channel Digital Input Board | ||||||||||||
| Availability (low quantity): |
Stock - 2 weeks | ||||||||||||
| Pricing (Budgetary, Per unit, US Dollars): |
|
Product Accessories
| 115-7623/2618 | Optional 26 conductor ribbon cable, IDC connector on each end |
|---|---|
| 115-7623/5018 | Optional 50 conductor ribbon cable, IDC connector on each end |
| 121-0003-48 | SNAPTRACK®, 3" W x 48" L |
| 121-0004 | DIN Rail mounting clip for use with SNAPTRACK® |
| 121-0005-39 | DIN rail, 35.0 x 7.5mm (EN50022-35), 39" L |
